Search found 166 matches

by om_tech_support_JS
Wed Nov 22, 2017 1:14 pm
Forum: Stepper Motors and Controls
Topic: Stepper Motor with Driver combination clarification
Replies: 3
Views: 19

Re: Stepper Motor with Driver combination clarification

Hi essenceindia, In regards to your post, the CVD228(BR)-K driver would have the most optimized performance as it was originally tested with the PKP264 frame size motors. However, since your motor only requires 2.0 A/phase, then the CVD223-K driver could also be used with this motor as the maximum o...
by om_tech_support_JS
Wed Nov 22, 2017 8:51 am
Forum: Stepper Motors and Controls
Topic: Stepper Motor with Driver combination clarification
Replies: 3
Views: 19

Re: Stepper Motor with Driver combination clarification

Hi essenceindia, Good Questions! Starting with the motor and driver combination, I would actually recommend going with either the CVD228-K or CVD228BR-K driver due to the size of the motor. The first being the board type driver and the second has a mounting bracket. I have linked the comparison belo...
by om_tech_support_JS
Tue Nov 21, 2017 11:53 am
Forum: Stepper Motors and Controls
Topic: Stepper Motor Sizing
Replies: 1
Views: 16

Re: Stepper Motor Sizing

Hi Engr. Wasiu, In regards to your post, I have the following definitions: Desired Resolution (feed per pulse) : This sets the desired smallest motion for your application. It determines the linear amount (inches or mm) that the system will move based on one pulse (or step) of the motor. Feed : This...
by om_tech_support_JS
Tue Nov 21, 2017 11:40 am
Forum: Speed Control Systems
Topic: ES01 Failure
Replies: 5
Views: 60

Re: ES01 Failure

Hi rydogdav,

Have you received the RMA email? If so, please proceed with the form if you have not done so already.
by om_tech_support_JS
Tue Nov 21, 2017 7:49 am
Forum: Speed Control Systems
Topic: ES01 Failure
Replies: 5
Views: 60

Re: ES01 Failure

Hi rydogdav, Please check your email for receipt of the RMA process. In the mean time, is there any issue with the fuse in your connection? Since the speed controller has no built-in fuse for overcurrent protection, the manual instructs to install a device for overcurrent protection (e.g. fuse) befo...
by om_tech_support_JS
Mon Nov 20, 2017 9:47 am
Forum: Speed Control Systems
Topic: ES01 Failure
Replies: 5
Views: 60

Re: ES01 Failure

Hi rydogdav, In regards to your post, I apologize that you have not received a response, however, I was unfortunately unable to locate an original request sent in. Did you originally contact via phone or email? Based on your description and the application, I would advise looking at the wiring of th...
by om_tech_support_JS
Mon Nov 20, 2017 9:04 am
Forum: Stepping Motors & Controls
Topic: CVK Series Controlling with PC
Replies: 4
Views: 60

Re: CVK Series Controlling with PC

Hi essenceindia, In regards to your post, since the CVK525BK package is a connector type package, I would recommend also getting the LCS04SD5 Driver Lead Wire Set (sold as an accessory) so that you would not need to make the motor, I/O, or Power cables that connect to the driver. We also offer the L...
by om_tech_support_JS
Mon Nov 20, 2017 8:42 am
Forum: Stepper Motors and Controls
Topic: BLE motor/driver control through Modbus
Replies: 5
Views: 68

Re: BLE motor/driver control through Modbus

Hi benjaminrigsby, In regards to your post, when you said that you have our "CC-link USB cable connected to the driver," were you referring to the CC05IF-USB ? The CC05IF-USB cable will only allow you to connect our product to the MEXE02 software, but cannot be used as the communication ca...
by om_tech_support_JS
Thu Nov 16, 2017 8:44 am
Forum: Stepping Motors & Controls
Topic: CVK Series Controlling with PC
Replies: 4
Views: 60

Re: CVK Series Controlling with PC

Hi essenceindia, In regards to your post, the CVK525BK package consists of a motor (with a double shaft) and a driver. This driver is a pulse input type driver , therefore, you will need to provide this package with pulse and direction signals from an external controller. You can reference the I/O s...
by om_tech_support_JS
Wed Nov 15, 2017 3:20 pm
Forum: Stepper Motors and Controls
Topic: AZ Series Interface Control Documentation (ICD)
Replies: 14
Views: 553

Re: AZ Series Interface Control Documentation (ICD)

Hi Saad, In regards to your post, using the 24 VDC power supplies would be our recommendation for the SCX11 controller and AZD-K driver. With that being said, each product will draw the current that it needs. Therefore, your power supply will need to have a minimum of the combined current values. Fo...
by om_tech_support_JS
Mon Nov 13, 2017 2:07 pm
Forum: Stepper Motors and Controls
Topic: BLE motor/driver control through Modbus
Replies: 5
Views: 68

Re: BLE motor/driver control through Modbus

Hi benjaminrigsby, In regards to your latest post, the value that you write to the 007Dh (125 decimal) register will be dependent on the binary code that is created from turning on the specific bits. For instance: If you want to run Speed No. 0 in the forward direction. Then you would turn on bit 3....
by om_tech_support_JS
Mon Nov 13, 2017 12:58 pm
Forum: Stepper Motors and Controls
Topic: BLE motor/driver control through Modbus
Replies: 5
Views: 68

Re: BLE motor/driver control through Modbus

Hi benjaminrigsby, In regards to your post, the Speed Registers will have upper and lower values ( 1152 for Speed No. 0 Upper and 1153 for Speed No. 0 Lower). You can store up to 16 different speeds into the series of registers (Speed No. 0 ~ Speed No. 15). However, in order to have the motor move, ...
by om_tech_support_JS
Mon Nov 13, 2017 10:24 am
Forum: Linear and Rotary Actuators and Controls
Topic: Reset current position
Replies: 1
Views: 40

Re: Reset current position

Hi UE07, In regards to your post, the most common method to avoid getting the error is to create a wrap. Another alternative would be to turn on the P-Preset input which will change the current position to the value set for the position preset value (factory setting is 0). You also mentioned that th...
by om_tech_support_JS
Wed Nov 08, 2017 3:44 pm
Forum: Stepping Motors & Controls
Topic: AZ Series: Checking the Current Position of an AZ Driver via ASG and BSG outputs
Replies: 0
Views: 202

AZ Series: Checking the Current Position of an AZ Driver via ASG and BSG outputs

Q: I am using your AZD-A driver with the SCX11 controller. I want to be able to read the current position of the AZ series motor as the system may be turned off at the end of the night and turned on to start the next day. I was told that the AZD-AD driver has a Modbus register that can be read, howe...
by om_tech_support_JS
Fri Nov 03, 2017 1:18 pm
Forum: Stepper Motors and Controls
Topic: Using CVK series driver and motor with third party controller
Replies: 3
Views: 124

Re: Using CVK series driver and motor with third party controller

Hi JeraldGor,

In regards to your post, the SCX10 is a discontinued product that has been updated to the SCX11 controller. When looking at a controller for your application, I would recommend going with the SCX11:
https://catalog.orientalmotor.com/item/ ... ller/scx11
by om_tech_support_JS
Thu Oct 26, 2017 2:41 pm
Forum: Stepping Motors & Controls
Topic: Microstepping, Accuracy, and Torque
Replies: 5
Views: 2346

Re: Microstepping, Accuracy, and Torque

Hi timoluca, In regards to your correction, the original response included the statement: " Microstepping with our step motor drivers will not decrease your motor's torque output. " The key point is that our driver is smart enough to adjust the current to keep the torque constant. In a gen...
by om_tech_support_JS
Thu Oct 26, 2017 6:48 am
Forum: Stepping Motors & Controls
Topic: Microstepping, Accuracy, and Torque
Replies: 5
Views: 2346

Re: Microstepping, Accuracy, and Torque

Hi timoluca,

In regards to your post, our driver will monitor the current on the windings. Based on the monitored current, the driver will then make an adjustment in order to optimize the torque. This function is the current correction (or compensation).
by om_tech_support_JS
Thu Oct 19, 2017 12:58 pm
Forum: Stepping Motors & Controls
Topic: AZ series: Wiring the HWTO input using a switch
Replies: 0
Views: 34

AZ series: Wiring the HWTO input using a switch

Q: I have the AZD-CD driver and I am attempting to wire the HWTO input. From the manual, it looks like I need to supply a voltage to the input in order to make it work. However, the system comes with jumper connections. I want to use a simple dry contact connection that I will break when I want to a...
by om_tech_support_JS
Tue Oct 17, 2017 12:54 pm
Forum: Stepper Motors and Controls
Topic: problem About the Changes That I Made on A Original Circuit
Replies: 1
Views: 87

Re: problem About the Changes That I Made on A Original Circuit

Hi Barlioh, In regards to your post, we are product experts on the components that we manufacture and unfortunately, we do not have experience with converter circuits. Therefore, we are unable to provide further insight than what you have determined. For something like this, I would recommend that y...
by om_tech_support_JS
Thu Oct 12, 2017 2:29 pm
Forum: Stepper Motors and Controls
Topic: 5-phase motor wire color connectioin to UDX5105
Replies: 7
Views: 163

Re: 5-phase motor wire color connectioin to UDX5105

Hi michael9422,

The winding configuration for the USX5105 is for a star winding.
by om_tech_support_JS
Wed Oct 11, 2017 1:01 pm
Forum: Stepper Motors and Controls
Topic: 5-phase motor wire color connectioin to UDX5105
Replies: 7
Views: 163

Re: 5-phase motor wire color connectioin to UDX5105

Hi michael9422,

Please see the picture below for the dip switches:
UDX5105 dip switches.png
UDX5105 dip switches.png (439.08 KiB) Viewed 134 times
by om_tech_support_JS
Tue Oct 10, 2017 2:21 pm
Forum: Stepping Motors & Controls
Topic: AZ: Stop and Z-HOME from a single input
Replies: 0
Views: 60

AZ: Stop and Z-HOME from a single input

Q: I have an application where I have a limited number of buttons that I can use for my application. I am trying to keep the application simple by only having two buttons. One button needs to be my run motion which will cut a piece of wood. This motion will need to go out the full length of the boar...
by om_tech_support_JS
Tue Oct 10, 2017 11:21 am
Forum: Stepper Motors and Controls
Topic: 5-phase motor wire color connectioin to UDX5105
Replies: 7
Views: 163

Re: 5-phase motor wire color connectioin to UDX5105

Hi michael9422, Unfortunately I do not have any information on the OEM or what is custom on that motor. (I am assuming that it has a custom wiring color and possibly some other customization(s) for the OEM's machine). My system only states that it was a custom Japanese part number. Therefore, you wo...
by om_tech_support_JS
Tue Oct 10, 2017 7:32 am
Forum: Stepper Motors and Controls
Topic: 5-phase motor wire color connectioin to UDX5105
Replies: 7
Views: 163

Re: 5-phase motor wire color connectioin to UDX5105

Hi michael9422, Were the C4893-9015HGEA1 and UDX5105 part of the same machine, or was this being used in a new application? The C4893-9015HGEA1 is a custom made part number for an original equipment manufacturer. Therefore, any information on the specifications, dimensions, and wiring for this unit ...
by om_tech_support_JS
Thu Oct 05, 2017 9:09 am
Forum: Stepper Motors and Controls
Topic: AZ Series Interface Control Documentation (ICD)
Replies: 14
Views: 553

Re: AZ Series Interface Control Documentation (ICD)

Hi Saad, With the AZD-K driver, you can use the SCX11 controller to send the pulse and direction signals in order to get the motor to move. The USB to mini B connection on the SCX11 controller will only be able to be used with the IMC (Immediate Motion Creator) Software that we have as a free downlo...

Go to advanced search