Search found 110 matches

by om_tech_support_JS
Mon Jun 26, 2017 12:14 pm
Forum: Stepper Motors and Controls
Topic: Connection of SCX11 and AZD-K
Replies: 5
Views: 70

Re: Connection of SCX11 and AZD-K

Hi cpede, In regards to your response, the difference between 1-pulse mode and 2-pulse mode can be found on page 25 of the AZD-K manual which I have linked below: AZD-K manual: http://www.orientalmotor.com/products/pdfs/opmanuals/HM-60249E.pdf 1-Pulse Mode vs 2-Pulse Mode.png One pulse input mode is...
by om_tech_support_JS
Mon Jun 26, 2017 11:00 am
Forum: AC Motors
Topic: Driver My LED
Replies: 2
Views: 18

Re: Driver My LED

Hi jimmy1995,

In regards to your post, we are unfortunately not familiar with the MAX16814 as this is a part not manufactured by Oriental Motor. Therefore, we are unable to provide you with any suggestions or verification on its use for your application.
by om_tech_support_JS
Mon Jun 26, 2017 10:50 am
Forum: Stepper Motors and Controls
Topic: Alpha Driver ASD30E-A-B1 and ASD30E-A Compatability
Replies: 1
Views: 14

Re: Alpha Driver ASD30E-A-B1 and ASD30E-A Compatability

Hi KevinEarlWood, The -B1 at the end of the ASD30E-A-B1 part number indicates that there was a customization done to this motor for an Original Equipment Manufacturer (OEM). We do not offer after-market support or sale of this product. You would need to contact the maker of the machine for any speci...
by om_tech_support_JS
Thu Jun 22, 2017 10:47 am
Forum: Stepper Motors and Controls
Topic: Connection of SCX11 and AZD-K
Replies: 5
Views: 70

Re: Connection of SCX11 and AZD-K

Hi cpede, In regards to your response, your connection from the SCX11 to the AZ driver is correct. There are a few things that I would like for you to check. 1.) What is the voltage switch set to on the SCX11 (5 VDC or 24 VDC?) 2.) What is the pulse mode of the driver and the controller? Both modes ...
by om_tech_support_JS
Tue Jun 13, 2017 1:03 pm
Forum: Speed Control Systems
Topic: Select BLDC motor for AGV
Replies: 4
Views: 78

Re: Select BLDC motor for AGV

Hi cokthemhok, Your calculations look good, however, there seems to be an error with your inertia of the wheel. This value should come out to 0.0 0 5 instead of 0.05. Taking into account the inertia of the AGV and load is what is the most important, this change in the value has no drastic affect on ...
by om_tech_support_JS
Mon Jun 12, 2017 1:02 pm
Forum: Speed Control Systems
Topic: Select BLDC motor for AGV
Replies: 4
Views: 78

Re: Select BLDC motor for AGV

Hi cokthemhok, What value did you calculate for the load inertia? In order to select a motor, the speed , torque , and inertia values will all be required. In order to determine these values, a sizing will need to be completed to calculate for these values. If you would like, we can size this applic...
by om_tech_support_JS
Mon Jun 12, 2017 12:48 pm
Forum: Stepper Motors and Controls
Topic: Connection of SCX11 and AZD-K
Replies: 5
Views: 70

Re: Connection of SCX11 and AZD-K

Hi cpede, In regards to your questions, the ARD-K driver is a pulse input type driver. This driver is unique from our other pulse input type drivers as it allows for a few methods of control. The first method is to send pulse and direction signals from an external controller. The SCX11 is an externa...
by om_tech_support_JS
Thu Jun 08, 2017 2:36 pm
Forum: Stepper Motors and Controls
Topic: sequential motor operations via RS-485
Replies: 2
Views: 79

Re: sequential motor operations via RS-485

Hi alands,

Is your question in regards to a previous post that you had?
viewtopic.php?f=3&t=6018&p=10273#p10273


Using direct data operation commands does not allow for sequential motor operations.
by om_tech_support_JS
Thu Jun 08, 2017 2:23 pm
Forum: Stepper Motors and Controls
Topic: Command by Distance & Time?
Replies: 1
Views: 47

Re: Command by Distance & Time?

Hi alands,

In regards to your application, the AZD controller does not have a function which can alternate between 7 and 8 Hz. Therefore, the alternation between 7 Hz and 8 Hz would need to be a function of your control method which is communicating through RS-485 Modbus.
by om_tech_support_JS
Wed May 31, 2017 8:00 am
Forum: Stepper Motors and Controls
Topic: Integrated board with 6 stepper 5 phase drivers - Need HELP
Replies: 1
Views: 99

Re: Integrated board with 6 stepper 5 phase drivers - Need HELP

Hi George. Unfortunately, the A6902-046 part number is a proprietary product which we had custom built for an original equipment manufacturer. We do not offer after-market support or sale of this product. Therefore, you would need to contact the maker of the machine for any specifications, support, ...
by om_tech_support_JS
Fri May 26, 2017 2:25 pm
Forum: Linear & Rotary Actuators and Controls
Topic: Minimum Speed of the DRL Series
Replies: 0
Views: 75

Minimum Speed of the DRL Series

Q: I have an application for a syringe pump and I need to know what the minimum speed of your DRL Compact Linear Actuators are I see the maximum speed is shown in the catalog and on your webpage, however I want to know the slowest that I can make it operate. A: The lowest frequency setting for the D...
by om_tech_support_JS
Tue May 23, 2017 2:12 pm
Forum: General Discussion
Topic: Can anyone tell me what's wrong with servo motor control?
Replies: 2
Views: 145

Re: Can anyone tell me what's wrong with servo motor control?

Hi Barlioh, Unfortunately we are unfamiliar with the syntax for the PIC12F675 code. However, if you are using the NX series servo motor package, then this package is a pulse input type package. Therefore, it will require pulse and direction signals from you PLC. Since the amount of pulses sent to th...
by om_tech_support_JS
Wed May 17, 2017 2:23 pm
Forum: Stepping Motors & Controls
Topic: DC Driver for PK596 Stepper Motor
Replies: 2
Views: 95

Re: DC Driver for PK596 Stepper Motor

Hi Ghadeer, The PK596BE1-H100 motor and RKD514H-C driver were part of our RK series motor and driver combination. These two units were designed to operate together and the PK596BE1-H100 motor was never package nor tested with a 24 VDC driver. Please note that testing the PK596BE1-H100 motor with a 2...
by om_tech_support_JS
Wed May 17, 2017 12:54 pm
Forum: Stepping Motors & Controls
Topic: Electromagnetic Brake Operation for Stepper Motors compared to Brushless DC motors.
Replies: 0
Views: 271

Electromagnetic Brake Operation for Stepper Motors compared to Brushless DC motors.

Q: I am using the AZD-AD driver and my stepper motor has an electromagnetic brake. I have used your BX2 series in the past and am used to the operation of the brake with this motor. However, for the AZ series, when I complete a motion, I do not hear the electromagnetic brake engage. I want the brake...
by om_tech_support_JS
Fri May 12, 2017 7:28 am
Forum: Speed Control Systems
Topic: BXS460C-A-3, Brushless DC Motor Speed Control System
Replies: 1
Views: 192

Re: BXS460C-A-3, Brushless DC Motor Speed Control System

Hi cbbeh In regards to your question, we manufacture various motor products which are typically used in industrial applications. In these types of applications, the noise specification is not a main consideration for the application. Furthermore, the noise generated may be dependent on the speed, lo...
by om_tech_support_JS
Mon Apr 17, 2017 2:17 pm
Forum: Stepper Motors and Controls
Topic: Having trouble driving 0.36deg stepper motor with ARD-K and Galil DMC 40x0 controller
Replies: 3
Views: 390

Re: Having trouble driving 0.36deg stepper motor with ARD-K and Galil DMC 40x0 controller

Hi pfranco, We offer both Sinking and Sourcing connections for our Inputs on the driver, however, the pulse signals will be the same whether the driver is wired in either Sink or Source. Please reference the diagrams below. ARD-K Sink Connection.png ARD-K Source Connection.png As you can see from th...
by om_tech_support_JS
Wed Apr 12, 2017 12:30 pm
Forum: Stepper Motors and Controls
Topic: Having trouble driving 0.36deg stepper motor with ARD-K and Galil DMC 40x0 controller
Replies: 3
Views: 390

Re: Having trouble driving 0.36deg stepper motor with ARD-K and Galil DMC 40x0 controller

Hi pfranco, In regards to your issue, it appears that your initial setup was correct. Checking the brake and having the C-ON input connected are two things that could have prevented the operation had you not checked those in the first place. Once the brake has power and the C-ON input is ON, then th...
by om_tech_support_JS
Mon Apr 10, 2017 9:29 am
Forum: Servo Motors & Controls
Topic: NX Series Driver Alarm Output
Replies: 4
Views: 285

Re: NX Series Driver Alarm Output

Hi NateD, If the other outputs are not working as well, then there is either an issue with the output terminal or the wiring to the output terminal. If the resistor was not originally used when wiring the 24 VDC power supply, then it is possible that the output was damaged due to the access current ...
by om_tech_support_JS
Fri Apr 07, 2017 6:15 am
Forum: Servo Motors & Controls
Topic: NX Series Driver Alarm Output
Replies: 4
Views: 285

Re: NX Series Driver Alarm Output

Hi NateD, In regards to your question, the outputs on the NX driver are open collector type outputs. Therefore, the output will require a voltage supplied to it. The NX driver can accept 30 VDC or less and the amperage must be limited to 10 mA or less . Therefore, you will need to connect a resistor...
by om_tech_support_JS
Thu Apr 06, 2017 12:30 pm
Forum: Stepper Motors and Controls
Topic: PLEASE HELP! How to send info from PLC to SCX11.
Replies: 3
Views: 230

Re: PLEASE HELP! How to send info from PLC to SCX11.

Hi jesus666viz, In regards to your request, once the ID number has been assigned using the command ID= ( page 257 ), then you can use the command @ ( page 179 ) to select the controller. Once the controller is selected, then you can use the RUN command ( page 330 ) to execute a sequence. http://www....
by om_tech_support_JS
Wed Apr 05, 2017 9:36 am
Forum: Stepper Motors and Controls
Topic: PLEASE HELP! How to send info from PLC to SCX11.
Replies: 3
Views: 230

Re: PLEASE HELP! How to send info from PLC to SCX11.

Hi jesus666viz, For support on the PLC, you would need to contact the manufacturer of the PLC. As for the SCX11 controller, it is programmed by RS232C. Typically, you would use our GUI software to program the controller and use the PLC to trigger inputs for selecting your program. SCX11 Software: ht...
by om_tech_support_JS
Wed Mar 22, 2017 9:27 am
Forum: Stepper Motors and Controls
Topic: HELP! How to program PKA566KD stepper motor
Replies: 1
Views: 194

Re: HELP! How to program PKA566KD stepper motor

Hi JZ, In regards to your question, the PKA566KD stepper motor is an All-in-One stepper motor package. The driver which is part of the All-in-One system is a built-in controller (stored data) type driver. This product has the label FLEX which means that you can control the motor via I/O, Modbus, or ...
by om_tech_support_JS
Wed Mar 22, 2017 9:07 am
Forum: Stepper Motors and Controls
Topic: What dows "Holding Torque Tb"'s "b" mean?
Replies: 4
Views: 269

Re: What dows "Holding Torque Tb"'s "b" mean?

Hi colemanlee, The "calculation software" and attachment which you provided are not available for the OM USA branch. From the part number, PKP268D28A-L which is the Japanese version, I can verify that the Holding torque is 2.3 N-m and the Rotor Inertia is 490 x10^-7 [kg-m^2]. For the true ...
by om_tech_support_JS
Mon Mar 20, 2017 7:43 am
Forum: General Discussion
Topic: Where is 162VDC speed – torque graph for UMK245BA?
Replies: 1
Views: 173

Re: Where is 162VDC speed – torque graph for UMK245BA?

Hi colemanlee, It appears that the same graph was used in this post. Since this post was made, the UMK245BA package has been discontinued. However, you can still reference the speed torque curve of the UMK245BA package from the link below: http://catalog.orientalmotor.com/image?cid=1002&imgname=...
by om_tech_support_JS
Mon Mar 20, 2017 7:05 am
Forum: Stepper Motors and Controls
Topic: What dows "Holding Torque Tb"'s "b" mean?
Replies: 4
Views: 269

Re: What dows "Holding Torque Tb"'s "b" mean?

Hi colemanlee,

In regards to your question, is there a specific product which you are referring to that shows the Holding Torque as Tb? Was this reference pulled from a manual or our catalog?

Go to advanced search