CRK Stored Program Controller Motion Creator Software

Discuss Stepper motors, Drivers, Controllers, GUI's and related Accessories here.
cowboy
Posts: 2
Joined: Thu Oct 06, 2011 7:03 pm

CRK Stored Program Controller Motion Creator Software

Postby cowboy » Thu Oct 06, 2011 7:19 pm

Hi

i purchased the CRK series stepping motor and installed the MEXE02 software which came with the motor, and used it, it works well, but now we are going to develop our own control program, i have discovered the sample code and downloaded the CRK motion creator software program, but now the problem is the software cannot connect the stepping motor driver (CRD507-KD), so can anyone help?

thank you

User avatar
omsupport1
Posts: 99
Joined: Thu Nov 19, 2009 10:34 am

Re: CRK Stored Program Controller Motion Creator Software

Postby omsupport1 » Fri Oct 07, 2011 9:12 am

cowboy,

Thank you for using products form Oriental Motor!

The answer to your question is quite simple. The MEXE02 software works with the CRD507-KD driver/controller that you have. The Motion Creator program that you downloaded is for a different driver/controller part #, CRD507-KP.

Both products use RS-485 as their communication protocol, but the "language" is different.

Does this help you?

Let us know if there is anything else I can do for you.
Oriental Motor Product Forum Support
forum@orientalmotor.com

admin
Site Admin
Posts: 1
Joined: Wed Sep 02, 2009 4:43 am

Re: CRK Stored Program Controller Motion Creator Software

Postby admin » Fri Oct 07, 2011 9:15 am

This topic has been moved to the "Stepping Motors and Controls" area

cowboy
Posts: 2
Joined: Thu Oct 06, 2011 7:03 pm

Re: CRK Stored Program Controller Motion Creator Software

Postby cowboy » Mon Oct 10, 2011 8:45 pm

Hi

firstly thank you for your reply

i am new for this motor, and follows RS485 communication modbus protocol shown in the instruction manuals, i try my code, it still not working, so currently i have two problem:
1. i made one rs485 cable with rj45 connector and db9 female connector in each end, with my pc, i have installed moxa card which gives 4 serial ports with db9 connector,i am not sure my wiring is correct or not? so anyboy can help to check?
rj45 db9
2 GND to 5 GND
3 TR+ to 8 tx+
6 TR- to 2 tx-
by the way i an using 2 wires connection

and sw2 setting from 1 to 4 is off, off, off, on
sw1 set to 1
sw3 set to on

2.any one can help to generate a sample code to perform a absolute move? thank you

i am using CRD507-KD driver

thank you

User avatar
omsupport1
Posts: 99
Joined: Thu Nov 19, 2009 10:34 am

Re: CRK Stored Program Controller Motion Creator Software

Postby omsupport1 » Tue Oct 11, 2011 11:02 am

Are the moxa card outputs RS-485?

Can you give me the moxa card part #?

What baud rate are you using?

I will look into it for you.
Oriental Motor Product Forum Support
forum@orientalmotor.com

mnedgeppolo
Posts: 14
Joined: Thu Aug 13, 2015 4:01 am

Re: CRK Stored Program Controller Motion Creator Software

Postby mnedgeppolo » Thu Aug 13, 2015 4:18 am

What I read I really liked it. Thank you for your information!

aldoned
Posts: 32
Joined: Mon Sep 14, 2015 3:03 am

Re: CRK Stored Program Controller Motion Creator Software

Postby aldoned » Thu Mar 24, 2016 1:50 am

Thanks for the info

artmuz62
Posts: 10
Joined: Wed Dec 14, 2016 4:58 am

Re: CRK Stored Program Controller Motion Creator Software

Postby artmuz62 » Wed Dec 14, 2016 11:48 pm

Hello! Very interesting topic, thank you raised it


Return to “Stepper Motors and Controls”

Who is online

Users browsing this forum: sedroljoxin and 1 guest